• Want to learn more?

  • Follow Leah on Twitter!

  • Most Recent Posts

  • Categories

  • Archives

  • Quilting Bloggers Logo
  • Advertisements

Quilt Binding By Hand

Binding is the last step, the final hurdle to finishing any quilting project. The way you choose to do it is completely up to you, but this is my method for binding a quilt using hand stitching to finish it off.

First cut your strips. I cut mine 2 1/4 inches wide. I like a nice tight fitting binding so that the edges of my quilt are plump and rounded. This also is important if you plan on entering a quilt into a show. Some judges look at binding in particular because a nice plump binding means that the edge won’t form a sharp crease and wear out faster from being drug around.

So how many strips should you cut? Well, I employ the very scientific and mathematical process of hold it up and guess. I cut a strip or two and hold them against the side of the quilt. If you can pretty much eye ball how many strips you need to cover two sides (ex: 2 strips along the top and 1 strip along the side) then just double that number and add one and you have the amount of strips to cut (7 strips). I always like to add one so that way I’m sure to have a lot of room at the end to play with.

So once the strips are cut, they need to be sewn together. You can either sew the pieces together using a miter seam or a straight seam. Honestly, I seam my binding together with a mitered seam, but I don’t see what is wrong with a straight seam if that’s what you’re comfortable with. I’m not sure that they will wear any different at least. Fold the binding in half lengthwise and press so that the seams are to the inside.

Here’s the fun part. Put on a walking foot and let’s stitch on this binding. Now for hand stitched binding you need to attach the raw sides of the binding to the right side of the quilt. This way, when you fold over the fabric it will be on the back of the quilt. This way you will have a nice smooth look on the front and the hand stitches will face the back. When you start, leave about a 10 – 12 inch tail of binding above your starting place. Also try to start in the middle of the quilt. You want to try to avoid having a seam fall right over a corner.

Stitch on the binding, sewing through all layers to 1/4″ before the corner. This picture to the left illustrates this step. I included a tape measure to try to show that the stitching stops 1/4″ from the edge. Take the quilt off the machine and finger press the binding up into a 45 degree angle. The picture to the right shows this step.

Now fold the binding strip down along the next side. It took so long for me to get my brain around all this folding! Check out this picture below to be sure you’ve got the right idea. You want these edges to match up perfectly, with the fabric straight and crisp. If the miter is sewn sloppy then it will only come out crooked.

Start stitching again 1/4″ from the edge. Repeat again for each corner. You are going to have a triangular flap of fabric that seams to wave in the wind after you sew each corner. This is correct! The folded triangle will open up and fold over the rough edges to form the mitered binding. When you get 10″ from the binding tail you left at the beginning stop sewing and reverse to lock. Take the quilt off the machine.

Now this is the tricky part and I still get a bit turned around with it sometimes. Lay the two ends of binding over each other and smooth it flat so that they are straight with the edge and even. Gently take the right hand piece and open it up on top of the left hand side so that the two pieces are open and right sides together. Run a pin through the middle where these two pieces cross. Now hold this carefully in place and move the right hand piece so that it is perpendicular to the left hand piece (like and upside-down ‘L’). Stitch a miter seam across this binding. Finger press the seam open and then fold binding back into place along side.

Reattach your walking foot and sew through all layers to finish.

Now the hand stitching part. Take the quilt off the machine and thread up a needle with thread that matches your binding color. I like to start about 10 inches from one edge. Tie a knot and hide it in the binding. Fold the binding over the raw quilt edge and begin to stitch it in place. When hand stitching I use very small stitches that are about 1/8″ wide. I got used to using these small stitches when I did beadwork with seed beads which is about the size of the stitches you want. You will want to maintain consistent, small stitches throughout the binding to hold it closed

When you get to a corner, fold the binding into a miter and stitch it tightly closed. I do not actually stitch up the diagonal fold, relying on the fold itself to hold it closed, but that is up to you. Here’s a picture of the right side of a perfectly executed binding miter.

At the end I tie a knot and hide it in the binding. Hand stitching the binding is more secure and in many ways looks better, but if time is an issue machine stitching the binding can definitely do the trick.


One Response

  1. Thanks. I’ve been trying to find out how small the stitching should be on sewing my binding. I figured pretty tiny and close together. It’s going to take forever to finish this part! 🙂

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )


Connecting to %s

%d bloggers like this: